-
CYC 1 to 1 Wiring Harness The 1 to 1 wiring harness connects your CYC Photon controller to the display. When using display only without a throttle. Keeps wiring slim and clean. The waterproof connectors ensure that they are equipped for outdoor use in any terrain. Includes:
- 1-1 wiring harness
-
CYC PHOTON Chainring Removal Tool
Finally available, the tool you’ve been waiting for! Securely plug in this 5-pronged tool to your center chainring retention ring to remove and install your chainring assembly. You can now easily switch between chainring sizes without contacting customer support for help.
- Full 360 degree contact - means no slipping.
- Built-in nut accepts a 22mm socket (or 7/8” if you must).
- Use an actual torque wrench for worry-free installs.
- Available in any color you want, as long as it’s black.
- Compatible with your CYC Photon eConversion System.
-
CYC 1 to 2 Wiring with Throttle Upgrade Option The 1 to 2 wiring harness connects your controller to the display and the throttle. The waterproof connectors ensure that they are equipped for outdoor use in any terrain. Includes:
- 1-2 wiring harness
- Optional Upgrade: Thumb throttle/ Full twist throttle/ Half-twist throttle
-
CYC 1 to 4 Wiring with Throttle Upgrade and Brake Sensor Option The 1 to 4 wiring harness connects your controller to the display, brake sensors, and throttle. The waterproof connectors ensure that they are equipped for outdoor use in any terrain. Includes:
- 1-4 wiring harness
- Thumb throttle/ full twist throttle/ half-twist throttle (optional)
- Magnetic brake sensors (optional)
-
CYC Speed Sensor and Bluetooth Module (X6 and X12 only)NOTE: This is for the X6 and X12 ControllerThe CYC speed sensors reads your speed via pulses detected from the speed sensor magnet as it moves with your wheel. This unit also houses the Bluetooth control module that is needed to connect to the CYC Ride Control app.- 7 Pin Male Connector- Includes Magnet- Installation GuidePlease read full description
-
The CYC eBike Headlights are ideal for night rides. With high and low beam lights, you can ride comfortably in lowlight situations. Includes:
- eBike low & high beam headlights
- 2x mounting sets for each light
- Bolts & hex keys needed
-
- Connector = XT-90 male & female connector
- Compatibility = X1 Stealth, X1 Pro, & Photon kits
- Power consuption = 18W per bulb
- Supported Voltages = 36V to 72V nominal voltage
- See full description for details.
-
ISIS Crank Arm Set, for your CYC Gen 3 and Photon CYC's ISIS crank arm set is a 5 degrees off-set, made to be paired with the Gen 3 and Photon kits. Ride with confidence knowing that your cranks won't give in even in extreme terrains. Includes:
- Left & Right side crank arm
- Length Options: 165mm or 175mm
- Material = 7075-t6 aluminium
- Compatibility = X1 Pro Gen 3, X1 Stealth Gen 3, Photon
-
The SW102 display with CYC specific firmware is integrated with the controller and the CYC Ride Control mobile app. It's convenient formfactor leaves you with plenty of space on your handlebars. Plug-n-play ready. Includes:
- SW102 display
- Nominal Voltage = 36-52V
- Waterproof = IP65
- Controller Compatibility = X6P, X6, & X12
- Operating temperature = -20°C to 60°C
- Screen specification = 1.3”OLED(64*128pixels)
-
The DS103 display with CYC specific firmware is integrated with the controller and the CYC Ride Control mobile app. It's easy-to-read formfactor gives you all the stats you'll need on the go. Plug-n-play ready. Includes:
- DS103 display
- Nominal Voltage = 36-52V
- Waterproof = IP65
- Controller Compatibility = X6P, X6, & X12
- Operating temperature = -20°C to 60°C
- Screen specification = 3.5” colored TFT (480*320pixels)
-
NEW X12 Controller - 5,000 Watts!
Be the first to receive the new, long awaited X12 Controller for a direct swap out on your X1 Pro Gen 3!- Runs 36v-72v eBike Batteries
- 8 Gauge Phase Wires
- The X12 Controller is a direct replacement for CYC X6 Controller on X1 Pro Gen 3 setups. DO NOT USE on CYC Stealth Motors!
- Same measurements as the X6 Controller, EXCEPT it is only 70mm longer. Mounts inside the same brackets of the X1 Pro Gen 3.
-
Swap your X1 Pro Gen 3
with the X1 Pro Gen 4 Motor (includes the NEW X12 Controller - 5,000 Watts)!
- Runs 36v-72v eBike Batteries
- 8 Gauge Phase Wires
- The X12 Controller is a direct replacement for CYC X6 Controller on X1 Pro Gen 3 setups. DO NOT USE on CYC Stealth Motors!
- Same measurements as the X6 Controller, EXCEPT it is only 70mm longer. Mounts inside the same brackets of the X1 Pro Gen 3.